| Customization: | Available |
|---|---|
| Warranty: | 1000000 Bending Times |
| Application: | Press Brake/Bending Machine |
|
Still deciding? Get samples of US$ 4000/Set
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| BHT Press Brake Machine Compensation Crowning Worktable | ||||||||||||
|
||||||||||||
| 1).Available Press Brake Machines Brand | Amada, Atlantic, Adira, Baykal, Beyler, Darley, EHT, Ermaksann, Durmazlar, Bystronic, Gasparini, Guifil, Haco,Imal, LVD Ivan, LVD, Mecos, Megobal, Promecam,Trumpfwila,Salvagnini, Safan, Weinbrenner,Yawei, Yangli,JFY,ACL,YSD,ZYMT,ADH,etc... | |
| 2).BHT Tooling Advantages | Taking into consideration our clients wishes, every day we work to satisfy our clients' needs, to increase our product list and tools quality. After receiving drawings of your bending tools we will advise you the proper tools or make design of special one. In future you will receive our technical consultation on any questions you have. A wide range of adapters and intermediates will help you to choose tools for press brake of rare mark. We produce our press brake tooling from high quality steel(42CrMo=SCM440=42CrMo4=4140), working surfaces are preciously grounded, standard will be whole body Total Hardening, the hardness can reach HRC47; Also we can do surface hardening by Laser, the the hardness can reach HRC60. |
|
| Center Accuracy:±0.02mm | ||
| Parallel Accuracy:±0.02mm | ||
| Vertical Accuracy:±0.02mm | ||
| 3). TYPES OF PRESS BRAKE TOOLS | Tools for press brake are considered "safety first", and dies with fall prevention grooves are now standard. | |
| Typical punch clamp types | ONE TOUCH TYPE / WITH SAFETY GROOVE | |
| Bending edge shapes | STANDARD PUNCH,GOOSENECK PUNCH,STRAIGHT PUNCH,SASH PUNCH,HEMMING PUNCH,THICK PLATE PUNCH | |
 |
||
| Typical die types and mounting methods | 1V Die, 2V Die, 4V Die | |
|
||
| 4). TOOL LENGTH | In the case of Amada type, there are 4 types such as standard types: L = 835mm, S = 415mm, A section = 835mm and B section = 800mm |
|
|
||
| 5). HOW TO READ THE TONNAGE CHART | |
| Check the tonnage chart before Bending. The tonnage chart is always specified in the tool catalog, and is also displayed on the machine as a nameplate where it is easy to see. Basically, you can read the conditions other than pressure in the chart below. Knowing this tonnage chart deeply or shallowly will make a big difference in worker safety and product finish. It greatly affects machine specifications, tool selection, product accuracy and quality, so let's grasp the contents and use them for safe work. First of all, read the following contents from the chart below. 1: Minimum flange length (b) 2: V-width (V-opening) of tool used for bending (V) 3: Required tonnage to bend 1m long material (F) [ Right figure, symbol of tonnage chart ] V=V-width (V-opening) b=Minimum flange length ir=Inner bend radius t=Material thickness (Tensile strength 40~50kg/mm) *Tensile strength for Stainless steel (Inox) 60~75kg/mm, Aluminum 25~45kg/mm F=Pressure par meter (kN/m) |
The values in the tonnage chart are based on "bottoming" and "SS material", so the tensile strength etc. must be taken into account depending on the processing conditions.The values in the tonnage chart are based on "bottoming" and "SS material", so the tensile strength etc. must be taken into account depending on the processing conditions. |
| 6). MINIMUM FLANGE LENGTH | |
| To complete the bending, the material must be on both shoulders of the die to the end. The minimum flange length is expressed by the following formula based on 90° bending. b=( V/2 ) x √2≒0.7V |
|
| 7). V width selection and basic setting of ir (inner R) | ||||
| V-WIDTH | ||||
|
Bending Method
|
V-Width
|
Features | ||
|
Bottoming
|
Material thickness
|
ecause of the bending process that is used most often, the patterns for V-grooves are also finely divided.
|
||
|
0.5 - 2.6
|
3.0 - 8.0
|
9.0 - 10
|
||
|
6×t
|
8×t
|
10×t
|
||
|
Partial Bending
|
12 - 15×t
|
Since an arbitrary angle bending is taken into consideration, the V-width is set so that bending accuracy is easily stabilized.
Approximately twice as much as bottoming.
|
||
|
Coining
|
5 - 6×t
|
The purpose is to reduce inner radius and reduce the amount of bite at the tip of the punch.
|
||
|
iR (inner radius)
|
||||
|
Bending Method
|
iR (inner radius)
|
Features
|
||
|
Bottoming
|
≒V/6
|
Base values for maintaining safe and stable accuracy, such as punch tip radius and spring-back amount.
|
||
|
Partial Bending
|
When high accuracy is required, use a bottoming type tool.
|
|||
|
Coining
|
Care must be taken when using a bottoming die because iR increases and extra pressurization is required.
|
|||
| 8). BHT Tooling Processing Equipments: |
|
| 9).BHT Tooling Testing equipments: CMM 2.5 Dimension (Precision:0.001mm),Microscope(Precision:0.001mm),Profile projector(Precision:0.001mm),CMM 3 Dimension ( Precision:0.001mm),Hardness tester,Calipers,Micrometer, Protractor,Height gauge, Dial gauge, Coating Thickness Gauge, etc... |
|
| 10). BHT Tooling Package: Thick wooden box with Air Bubble Film inside |
|
| 11). BHT Tooling Photos for Reference: |
|
| 12). BHT have exported the products to 65 countries (Germany, Sweden, Hungary, Italy, Netherlands, Spain, Portugal, Czech Republic, Lithuania, Serbia, Greece, Malta, Austria, Kosovo, Turkey, Ukraine, Albania, Estonia, Belarus, Bulgaria, Bosnia, Croatia, Romania,USA, Brazil, Argentina, Mexico, Bolivia, Colombia, Canada, Peru, Chile, Australia, New Zealand, Rwanda, Egypt, South Africa, Tanzania, Nigeria, Botswana, Mauritius, Russia, Vietnam, India, Iran, Singapore, Uzbekistan, Thailand, Sri Lanka, Bangladesh, Malaysia, Kazakhstan, Philippines, Bahrain, Pakistan, United Arab Emirates, Kuwait, Saudi Arabia, Sudan, Jordan, Oman, Qatar, Syria, Israel, Yemen) |
|
|
){kind=link}